Bootcode Ver.1.23 for [TSTGL]
Build:Dec 14 2005 [21:38:16]
isUseRevClock=0
******* Product Information *******
----------------------------------
Product Name: TS-TGL(IENARI)
VER: 3.07
Date: 2006/2/7 10:42:52
----------------------------------
Firmware check:done.
>>root=/dev/md0
hit any key to Enter cmd mode.
If you type Return, you will get following selection:
>command mode
arg:
root=/dev/ram0 : initrd
root=/dev/md0 : hdd-rootfs
root=/dev/nfs ip=192.168.19.114:192.168.19.219 nfsroot=/tera_root : nfs-rootfs
Input Kernel arg [root=/dev/md0]:
Now Loading...done.
Now Booting
KERNELBASE=c0000000 r6=900030 r7=900052
cmd_line=root=/dev/md0 panic=5 BOOTVER=1.23
Memory BAT mapping: BAT2=128Mb, BAT3=0Mb, residual: 0Mb
Linux version 2.4.20_mvl31-ppc_terastation (root@develop) (gcc version 3.3.1 (MontaVista 3.3.1-7.0.13.0500039 2005-01-13)) #10 Tue Feb 7 10:42:29 JST 2006
BUFFALO Network Attached Storage Series
(C) 2002-2005 BUFFALO INC.
On node 0 totalpages: 32768
zone(0): 32768 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/md0 panic=5 BOOTVER=1.23
OpenPIC Version 1.2 (1 CPUs and 10 IRQ sources) at 80040000
decrementer frequency = 32.768000 MHz
calender invalid set default value
Calibrating delay loop... 174.48 BogoMIPS
Memory: 125200k available (1692k kernel code, 532k data, 68k init, 0k highmem)
Dentry cache hash table entries: 16384 (order: 5, 131072 bytes)
Inode cache hash table entries: 8192 (order: 4, 65536 bytes)
Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
Buffer-cache hash table entries: 8192 (order: 3, 32768 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
BUFFALO INC. RTC driver ver 1.00
MICON V2 (C) BUFFALO INC. V.1.00 installed.
MICON ctrl (C) BUFFALO INC. V.1.00 installed.
Kernel event proc (C) BUFFALO INC. V.1.00 installed.
LSP Revision 1
Starting kswapd
Disabling the Out Of Memory Killer
Journalled Block Device driver loaded
SGI XFS 1.3.0 with no debug enabled
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x80004600 (irq = 25) is a ST16650
ttyS01 at 0x80004500 (irq = 24) is a ST16650
RAMDISK driver initialized: 16 RAM disks of 15000K size 1024 blocksize
loop: loaded (max 8 devices)
eth0: RTL8169s/8110s Gigabit Ethernet driver 2.2+1 at 0xc9000f00, 00:16:01:01:12:b6, IRQ 16
PCI: 00:0b.0 PCI cache line size set incorrectly (0 bytes) by BIOS/FW, BUFFALO:it must be zero for PPC8241/8245
eth0: Auto-negotiation Enabled.
eth0: 100Mbps Full-duplex operation.
SCSI subsystem driver Revision: 1.00
ata1: SATA max UDMA/100 cmd 0xC9002C80 ctl 0xC9002C8A bmdma 0xC9002C00 irq 17
ata2: SATA max UDMA/100 cmd 0xC9002CC0 ctl 0xC9002CCA bmdma 0xC9002C08 irq 17
ent->port_ops->irq_handler 3222357644
probe begin
ata1: probe begin
ata1: probe-wait begin
ata1: dev 0 ATA, max UDMA/133, 976773168 sectors: lba48
ata1: dev 0 configured for UDMA/100
ata1: probe-wait end
ata2: probe begin
ata2: probe-wait begin
ata2: dev 0 ATA, max UDMA/133, 976773168 sectors: lba48
ata2: dev 0 configured for UDMA/100
ata2: probe-wait end
EXIT, returning 2
ata3: SATA max UDMA/100 cmd 0xC9004A80 ctl 0xC9004A8A bmdma 0xC9004A00 irq 20
ata4: SATA max UDMA/100 cmd 0xC9004AC0 ctl 0xC9004ACA bmdma 0xC9004A08 irq 20
ent->port_ops->irq_handler 3222357644
probe begin
ata3: probe begin
ata3: probe-wait begin
ata3: dev 0 ATA, max UDMA/133, 976773168 sectors: lba48
ata3: dev 0 configured for UDMA/100
ata3: probe-wait end
ata4: probe begin
ata4: probe-wait begin
ata4: dev 0 ATA, max UDMA/133, 976773168 sectors: lba48
ata4: dev 0 configured for UDMA/100
ata4: probe-wait end
EXIT, returning 2
scsi0 : sata_sil
scsi1 : sata_sil
scsi2 : sata_sil
scsi3 : sata_sil
Vendor: ATA Model: WDC WD5000AAKS-2 Rev: 12.0
Type: Direct-Access ANSI SCSI revision: 05
Vendor: ATA Model: WDC WD5000AAKS-0 Rev: 12.0
Type: Direct-Access ANSI SCSI revision: 05
Vendor: ATA Model: WDC WD5000AAKS-0 Rev: 12.0
Type: Direct-Access ANSI SCSI revision: 05
Vendor: ATA Model: WDC WD5000AAKS-2 Rev: 12.0
Type: Direct-Access ANSI SCSI revision: 05
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
Attached scsi disk sdc at scsi2, channel 0, id 0, lun 0
Attached scsi disk sdd at scsi3, channel 0, id 0, lun 0
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
Partition check:
sda: unknown partition table
SCSI device sdb: 976773168 512-byte hdwr sectors (500108 MB)
sdb: unknown partition table
SCSI device sdc: 976773168 512-byte hdwr sectors (500108 MB)
sdc: unknown partition table
SCSI device sdd: 976773168 512-byte hdwr sectors (500108 MB)
sdd: unknown partition table
physmap flash device: 400000 at ffc00000
Search for id:(20 20) interleave(1) type(1)
Search for id:(20 20) interleave(1) type(1)
Search for id:(00 00) interleave(1) type(1)
Search for id:(20 5d) interleave(1) type(2)
Found: ST M29W324DB
linkstation_flash: Found 1 x16 devices at 0x0 in 8-bit mode
number of JEDEC chips: 1
Using physmap partition definition
Creating 5 MTD partitions on "linkstation_flash":
0x00000000-0x00300000 : "mtd0"
0x00300000-0x00370000 : "mtd1"
0x00370000-0x00380000 : "mtd2"
0x00380000-0x00400000 : "mtd3"
0x00000000-0x00400000 : "mtd4"
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
ehci_hcd 00:0e.2: PCI device 1033:00e0
ehci_hcd 00:0e.2: irq 19, pci mem c9006f00
usb.c: new USB bus registered, assigned bus number 1
PCI: 00:0e.2 PCI cache line size set incorrectly (0 bytes) by BIOS/FW, BUFFALO:it must be zero for PPC8241/8245
ehci_hcd 00:0e.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29/2.4
hub.c: USB hub found
hub.c: 5 ports detected
usb-ohci.c: USB OHCI at membase 0xc9008000, IRQ 19
usb-ohci.c: usb-00:0e.0, PCI device 1033:0035
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 3 ports detected
usb-ohci.c: USB OHCI at membase 0xc900a000, IRQ 19
usb-ohci.c: usb-00:0e.1, PCI device 1033:0035
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid5 personality registered as nr 4
raid5: measuring checksumming speed
8regs : 312.800 MB/sec
32regs : 322.000 MB/sec
raid5: using function: 32regs (322.000 MB/sec)
md: multipath personality registered as nr 7
md: md driver 0.90.2 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP: Hash tables configured (established 8192 bind 16384)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: AppleTalk 0.18a for Linux NET4.0
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 2032k freed
VFS: Mounted root (ext2 filesystem).
date: invalid date `2005/12/ 1 00:00:06'
Thu Dec 1 09:00:06 JST 2005
linuxrc:choose operation (timeout 4[s])
1:RamRoot 2:SetDiskNo other:HddRoot ? -HddRoot-
-- rebuild mdadm.conf for md0 --
mdadm: cannot open /dev/ts_disk1_1: No such device or address
mdadm: cannot open /dev/ts_disk2_1: No such device or address
mdadm: cannot open /dev/ts_disk3_1: No such device or address
mdadm: cannot open /dev/ts_disk4_1: No such device or address
mdadm: No arrays found in config file
mdadm: md device /dev/md0 does not appear to be active.
/dev/md0: Invalid argument
mount: you must specify the filesystem type
Freeing unused kernel memory: 68k init
kmod: failed to exec /sbin/modprobe -s -k char-major-4, errno = 2
INIT: version 2.78 booting
Setting kernel variables ...
kernel.shmmax = 60000000
fs.xfs.sync_interval = 300
vm.bdflush = 40 500 0 0 500 500 60 20 0
... done.
[: 0: unexpected operator
Mounting local filesystems...
none on /dev/pts type devpts (rw,gid=5,mode=20)
Cleaning: /tmp .
Restore previous configuration files
Restore
Configuration network interface: lo eth0
INIT: Entering runlevel: 3
Starting ls_servd:starting on eth0
logger: not found
start start_server()
logger: not found
.: Can't open /etc/melco/info
/etc/melco/diskinfo not exist
Starting kernelmon:logger: not found
miconmon 0.4e
Starting processmon:processmon ver.1.00
logger: not found
/etc/melco/diskinfo not exist
grep: /etc/linkstation_release: No such file or directory
logger: not found
BUFFALO INC. TeraStation series TS-TGL (IENARI)
TS-TGL-EM login: